# How much does fence installation cost in Johns Creek?

> Fence cost in Johns Creek, GA: typical Atlanta-area ranges per foot for wood, vinyl, aluminum and chain link, gates, the $75 permit and what moves the price.

URL: https://uprightjohnscreekfencing.com/guide/fence-installation-cost/

Cost Guide

Typical Atlanta-area ranges per foot, what a Johns Creek permit adds, and the handful of things that move a fence price more than the material does.

Last Updated: November 5, 2026

A new fence in the Johns Creek area typically costs about **$20 to $30 per foot** installed for 6-foot wood privacy, **$20 to $40** for vinyl, **$25 to $50** for aluminum and **$8 to $24** for chain link. These are typical Atlanta-area budgeting ranges, not quotes. Gates, removing an old fence, slopes and rock, and the $75 Johns Creek residential permit are on top.

[Upright Johns Creek Fencing](https://uprightjohnscreekfencing.com/) prices [fences](https://uprightjohnscreekfencing.com/fence-installation/) across Johns Creek and north Fulton from a measured line, with the work done by licensed and insured fencing contractors. The rest of this guide explains what sits inside those ranges, so you can read an estimate line by line.

Key takeaways

- Material sets the starting range; length, gates and ground decide where in the range a job lands.
- Johns Creek charges $75 for a residential fence permit, and replacing a fence needs one too.
- Gates are priced separately. A walk gate typically adds $150 to $600; driveway gates add more.
- Slopes, rock, tight access and tear-out move the price more than most material upgrades.

## Typical ranges by fence type

| Fence type | Typical Atlanta-area range, per foot installed | What usually pushes it higher |
| --- | --- | --- |
| [Wood privacy](https://uprightjohnscreekfencing.com/wood-fence-installation/), 6 ft | $20 to $30 | Board-on-board style, 8-ft height, cedar instead of pine |
| [Vinyl](https://uprightjohnscreekfencing.com/vinyl-fence-installation/) | $20 to $40 | Privacy panels, taller heights, steep slopes that need stepping |
| [Aluminum or ornamental](https://uprightjohnscreekfencing.com/aluminum-fence-installation/) | $25 to $50 | Pool-rated styles, taller panels, decorative tops, racking |
| [Chain link](https://uprightjohnscreekfencing.com/chain-link-fence-installation/) | $8 to $24 | Black vinyl coating, heavier framework, taller fabric |

The low end of each range fits a long, straight, flat run on soft ground with good access. The high end fits shorter runs with several corners and gates, sloped yards and harder digging. A national figure is not a local rate; these ranges come from published Atlanta-area pricing.

## What moves a fence price

| What changes | Why it matters |
| --- | --- |
| Length and corners | Fixed costs spread over more feet on long runs; every corner and end needs a heavier, braced post |
| Height and style | Taller and solid fences catch more wind, so posts go deeper and closer together |
| [Gates](https://uprightjohnscreekfencing.com/gate-installation/) | Each gate needs its own posts, hardware and labor; double and driveway gates more |
| [Slope](https://uprightjohnscreekfencing.com/guide/fence-on-a-slope/) | Racking or stepping panels, longer posts and more cutting on the downhill side |
| Soil and rock | Clay needs drainage under each post; stony ground can stop an auger and slow every hole |
| Access | A narrow side yard or steep backyard means materials are carried and holes dug by hand |
| [Tear-out](https://uprightjohnscreekfencing.com/fence-replacement/) | Old posts set in concrete come out with their footings, and the debris is hauled away |
| Approvals | The permit, HOA drawings and any survey add cost and time before the first post |

## What’s inside a Johns Creek fence price

Some parts of a fence price have a public figure you can check; others depend on the yard and only show up on site.

| Part of the price | What sets it | Local figure |
| --- | --- | --- |
| Labor | Crew hours for layout, digging, setting and hanging | Fence erectors in the Atlanta metro earn a mean $20.40 an hour, versus $24.29 nationally ([BLS Occupational Employment and Wage Statistics](https://www.bls.gov/oes/), May 2025) |
| [City permit](https://uprightjohnscreekfencing.com/guide/johns-creek-fence-permit/) | Required for new and replacement fences | $75 residential, $100 commercial ([City of Johns Creek fee schedule](https://johnscreekga.gov/departments/community-development/)) |
| Utility locate | Required before powered digging | Requested through [Georgia 811](https://georgia811.com/) at least 3 business days ahead |
| Materials | Fence type, height, post size, hardware | No public local index; set by the material and style chosen |
| Footings | Depth, concrete and drainage base for the soil found | No public figure; depends on height, gates and what the auger hits |
| Survey | Needed when the line is close or uncertain | No public figure; quoted by a licensed surveyor |
| HOA review | Drawings and style details for the committee | No public figure; some HOAs charge their own review fee |

A wage is not a billing rate. The rate a contractor bills also carries insurance, licensing, vehicles, equipment, materials handling and overhead. The Atlanta-area mean for fence erectors sits about 16% below the national mean, so local labor is not what makes a Johns Creek fence expensive; approvals, gates, slopes and the ground usually are.

## Permit fees in Johns Creek and nearby

| City | Fence permit | Fee |
| --- | --- | --- |
| Johns Creek | Required for new and replacement fences | $75 residential, $100 commercial |
| [Sandy Springs](https://uprightjohnscreekfencing.com/service-areas/sandy-springs/) | Required for new and replacement fences and gates | Confirm with the city |
| Peachtree Corners | Not required unless the fence needs footers | None for most fences |
| Roswell | Not normally required; pool fences permitted with the pool | None for most fences |
| Milton | Required | $100 site fee and $25 administrative fee (confirm with the city) |

## Illustrative example budgets

These examples are illustrative, built from the typical ranges above. They are not quotes, and real yards vary.

| Example | Calculation | Illustrative total |
| --- | --- | --- |
| 150 ft of 6-ft wood privacy, one walk gate, Johns Creek permit | 150 x $20 to $30, plus $150 to $600 gate, plus $75 permit | About $3,225 to $5,175 |
| 120 ft of aluminum across a front yard, one walk gate | 120 x $25 to $50, plus $150 to $600 gate | About $3,150 to $6,600 |
| 200 ft of chain link around a rear yard, one walk gate | 200 x $8 to $24, plus $150 to $600 gate | About $1,750 to $5,400 |

Tear-out of an old fence, driveway gates, steep slopes and rock are not in these examples and would add to them.

Want a range for your own line?

The cost estimator works from your length, material, height and gates, with no phone call needed.

Call (678) 509-2926

## How to compare two fence estimates

Line the estimates up item by item. Check that both include the same length, height and style; the same number and size of gates; removal and haul-away of the old fence; who applies for the Johns Creek permit and who pays the $75 fee; and the Georgia 811 locate. Then look at the posts: their size, spacing and how deep they are set, and whether the holes get a drainage base. A lower price often means shallower posts or wider spacing, which shows up a few seasons later as a leaning fence.

If one estimate is much lower, ask what it leaves out rather than assuming the other is padded. To talk through a specific yard, call or send the details through the form below; a photo of the line and the gates helps.

## Questions about this guide

### How much does a 6-foot wood privacy fence cost in Johns Creek?

A typical Atlanta-area range is about $20 to $30 per foot installed for 6-foot wood privacy fence, so about $3,000 to $4,500 for 150 feet before gates, tear-out and the $75 Johns Creek residential fence permit.

### What does a fence permit cost in Johns Creek?

The City of Johns Creek's Community Development fee schedule lists a fence permit at $75 for residential property and $100 for commercial property. A permit is required for new fences and for replacements.

### Why do two estimates for the same fence differ so much?

Usually because they price different work: one includes tear-out, gates, post depth for a solid 6-foot fence and the permit, and the other leaves some of those out. Compare line by line, especially posts, gates and removal.

Want this answered for your own yard?

A site visit shows what the line, the slope and the rules mean for your fence.

Call (678) 509-2926

## More guides

Learn

Do you need a permit to build a fence in Johns Creek?

Yes, for every new fence and every replacement. This guide covers the permit, the zoning rules behind it, HOA approval, property lines, utilities, protected trees, and how the rules change in the cities around Johns Creek.

Decision Guide

Wood vs vinyl fence: which is better in Georgia?

Wood costs less to install and repairs easily; vinyl skips staining but cracks on impact and is not allowed everywhere nearby. The right answer depends on your lot.

Decision Guide

Is chain link cheaper than wood?

Usually, yes. Chain link costs less per foot and lasts a long time, but it gives no privacy and local rules limit where it can go.

Learn

How do you build a fence on a slope?

Two ways: racked, where the rails follow the grade, or stepped, where level sections drop at each post. The material and the dog usually decide which.

Decision Guide

Should you repair or replace your fence?

Repair when the damage is limited to a few posts, boards or a gate. Replace when posts are failing along the whole line, or when you want a different fence.